| Front Panel |
¢ Recess for stacking use  ¢¬ Protrusion for stacking use |
| View Applications > |
 Pulse Signal |
 CNT-723-CAN |
CAN Analog Output |
 PC PLC Oscilloscopes / Data Analyzers, etc. |
Freely set the full-scale value of the analog output.
Up to ¡Þ47-bit count, suitable for long-term endurance tests.
Repeatedly measures between two arbitrarily set numbers, such as 0 and 360.
Determines forward/reverse rotation with polarized output (¡Þ10V / ¡Þ5V).
Resets at the Z-phase edge, serving as a RING counter with zero cumulative error.
Measures by magnifying the deviation against the target angle.
For example, to stop at 5¡ë, set the target value to 5¡ë and the range value to
the analog full-scale value to perform magnified measurement during this interval.
Ideal for detailed angle experiments.
Upper: Full Scale
Lower: Count Value
Upper: Full Scale
Lower: Count Value [Rotation Count]r[Angle]
Upper: Full Scale
Lower: Count Value [Rotation Count]r[Degree/Minute/Second]
 |
Panel Mounting Bracket ATC-2 (Sold separately, set of 2) |
| Product Name | High-Speed Analog Output Pulse Counter |
| Model | CNT-723 / CNT-723-CAN |
| Input Section | |
| Number of Inputs | 1 point |
| Input Method | Single-phase, A/B-phase, UP/DOWN signal |
| Input Frequency | 0-2MHz |
| Input Circuit Characteristics | |
| General-Purpose Input | |
| Input Signal | Logic, Zero-cross (AC) |
| Trigger Level | Comparator Input: 0.00-10.00V (Up to 10Vp-p amplitude) CMOS Input: H >= 3.5V / L <= 1V |
| Input Sensitivity | 1Vp-p or higher (Comparator input) |
| Input Withstand Voltage | ±50V |
| Input Resistance | 100kΩ / 10kΩ |
| Input Coupling | DC / AC |
| AC Coupling Freq. Characteristics | 4Hz (-3dB, 6dB/oct) |
| Low-Pass Filter | None / 15kHz / 1.5kHz (-3dB, 6dB/oct) |
| Connector | BNC / Screwless terminal block (internally short-circuited) |
| Line Driver Input | |
| Input Signal | Line driver signal |
| Input Sensitivity | 1V or higher (differential voltage) |
| Input Withstand Voltage | ¡Þ25V (vs PULSE GND / differential voltage) |
| Recommended Line Driver | AM26LS31 equivalent |
| Terminator | None / 340Ω |
| Connector | Screwless terminal block |
| Common Items | |
| Input Pulse Width | 150ns or more (Both L and H levels) *When set to 5V CMOS/Line Driver |
| Phase Diff. / Overlap Width | 75ns or more (Both L and H levels) |
| Trigger Direction | Rising / Falling |
| Indicator | Blinks at pulse input / Lights up at high-speed pulse |
| Sensor Power Supply | +5V 150mA max +12V 120mA max |
| Display Section | |
| Display Device | 16×2 character dot character LCD (with LED backlight) |
| Calculation Section | |
| Update Time | 3.5μs or less (4.1μs or less during Z-phase processing) |
| Response Time | 7.6μs or less |
| Setting Storage | Non-volatile memory |
| Pulse Counter Capacity | ±47bit |
| Count Value Storage | Electric double-layer capacitor (Storage time: 6 hours or more) |
| Analog Output Section | |
| Number of Outputs | 1 point |
| Output Range | ¡Þ10V / ¡Þ5V |
| Output Resolution | 16bit (Approx. ¡Þ10.8V) |
| Calibration Output | 100% / 0% / -100% |
| Temperature Drift | ¡Þ200ppm/¡î or less |
| Output Accuracy | ¡Þ0.1% full scale or less @23¡î (Output range: 0-10V) |
| Linearity | ±0.1% full scale or less @23¡î (Output range: 0-10V) |
| Load Resistance | 4.7kΩ or higher |
| Output Zero Adjustment | ¡Þ200mV |
| Output Connector | BNC |
| Z-Phase Re-pulse Output | |
| Number of Outputs | 1 point |
| Output Logic | Same logic as the input signal |
| Output Level | 5V CMOS |
| Output Resistance | 51¦¸ |
| RS-232C Communication | |
| Standard | EIA-574 (RS-232C) |
| Communication Method | Asynchronous |
| Baud Rate | 9.6k / 19.2k / 38.4k / 57.6k / 115.2kbps |
| Transmission Format | Start bit: 1bit |
| Stop bit: 1bit | |
| Data length: 8bit | |
| Parity bit: None | |
| Flow Control | RTS / CTS |
| Communication Code | ASCII |
| Connector | D-sub 9-pin male (Use crossover cable for host connection) |
| Communication Data | Setting changes, count value reading |
| CAN Communication Option Model [CNT-723-CAN] | |
| Standard | CAN2.0B compliant |
| Terminating Resistor | None |
| Communication Speed | 1M / 500k / 250k / 125k / 100k / 50k / 20k / 10kbps |
| Format | Little endian / Big endian |
| ID Length | 11bit / 29bit |
| Numeric Format | Signed integer 16bit / 32bit / 48bit |
| Output Interval | 0-100ms (No output when set to 0ms) |
| Communication Data | Measurement value output, reset command reception |
| Connector | 1x D-sub 9-pin male |
| General Specifications | |
| Power Input | AC100-200V (50/60Hz) |
| Power Consumption | 30VA or less |
| Isolation | Sensor power supply & Signal input / Analog output / Power input / Case |
| Dimensions | 218W × 218D × 57H mm (including protrusions) |
| Operating Temp/Humidity | 0¡î to +40¡î / 85%RH or less (no condensation) |
| Storage Temp/Humidity | -10¡î to +60¡î / 85%RH or less (no condensation) |
| Operating Environment | No corrosive gases |
| Weight | Approx. 1.8kg |
| View Counter List |