Name |
Pulse counter with high speed analog
output |
Model |
CNT-723
|
Signal
Input |
Number
of inputs |
1 |
Input signal |
Single phase signal, A/B phase signal, UP/DOWN
signals |
Input
frequency range |
2MHz (Max.) |
Input
circuit characteristics |
Input
circuit
characteristics |
1) General
input signals |
Input signal |
Logic / zero cross (AC) |
Trigger level |
0.00 to 10.00V
2.5V (Logic input) |
Input sensitivity |
Min 1V p-p |
Input withstand voltage |
50V |
Input resistance |
100k
/ 10k
when pull-up to +5V : 1.36k |
Input coupling |
DC / AC |
AC coupling frequency characteristic |
4Hz (-3dB, 6dB / oct) |
Low-pass filter |
None / 15kHz (-3dB, 6dB
/ oct)/
150kHz (-3dB, 6dB / oct) |
Input connector |
BNC connector / screwless
terminal block (internal short circuit) |
2) Line driver input |
Input signal |
Line driver signal |
Input sensitivity |
Min. 1V (differential voltage) |
Input withstand voltage |
25V
(for GND)
25V
(differential voltage) |
Recommended line driver |
AM26LS31 or equivalent |
Terminator |
340
/ none |
Input connector |
Screwless terminal block |
Input
pulse width |
MIn. 150ns (both H level and
L level) *Logic input |
Trigger direction |
Rise / Fall |
Input indicator |
TRIG'D LED : Flash during pulse
input
(continuously light for high-speed pulse) |
Power supply for
sensor |
+5V     
: Max. 150mA
+12V : Max 120mA |
Display
|
Display |
16x2 character dot matrix LCD (LED back
light illumination) |
Display mode |
1) Count (direct count)
2) Degree (number of rotations + degree)
3) Degree Minute Second (number of rotations
+degree minute second)
4) Length (multi scaling) |
Arithmetic
Operation |
Pulse counter capacity |
47bit |
Set value storage |
Non-volatile memory |
Operation time |
Max. 3.5 s |
Analog response total time |
Max. 7.6 s |
Analog
Output |
Number
of outputs |
1 |
Output
voltage range |
10V
/ 5V |
Output resolution |
16bit (about 10.8V) |
Measurement mode |
Linear counter / Ring counter / Magnify |
Calibration
output |
+100% / 0% / -100% |
Temperature
fluctuation |
Max. 200ppm
/  |
Output
accuracy |
Max. 0.1%
full scale @23  |
Linearity |
Max. 0.1%
full scale @23  |
Load resistance |
Min. 4.7k |
Output zero adjustment range |
200mV |
Output connector |
BNC connector |
EIA-574 |
Connunications standards |
EIA-574 (RS-232C)
Setting change and reading of a measurement value) |
Communication system |
Asynchronous |
Communication
parameter |
Baud rate |
9.6kbps / 19.2kbps / 38.4kbps / 57.6kbps
/ 115.2kbps |
Start bit |
1bit |
Stop bit |
1bit |
Data length |
8 bits |
Parity bit |
none |
Communication code |
ASC |
General |
Power
supply input |
AC100V to 240V (50Hz / 60Hz) |
Power
consumption |
Max. 30VA |
Isolation |
Sensor power source and signal input / analog
output / power supply input / housing |
Outside
dimentions |
57 (W)
218 (H)
218(D) mm
(2.24 (H)
8.58 (W)
8.58 (D) inches) |
Weight |
Approximately
1.8kg (without accesories) |
Operating
temperature & humidity limits |
0
to +40 / Max. 85%RH
(no dewing) |
Storage
temperature & humidity limits |
-10
to +60 / Max. 85%RH
(no dewing) |