Applications

How to check only specific CAN data / No need for expensive CAN analyzers

The CAN series is a reasonably priced 1-CH type CAN analog converter.
Operating from 7-60VDC (7-30VDC for CANL-24) or USB power supply (5V), the CAN series is compact and easy to use.

No need
Complicated setup		 No need
Expensive analyzer		 No need
Expensive diagnostic equipment

No CAN analyzer required, easy output confirmation at your fingertips.
Alarm output when abnormal value is detected.　[Option]

1CH　Display only 17,600 yen　(tax not included)
1CH　1ms analog output + 2 alarm outputs 53,000 yen　(tax not included) *Prices in Japan, vary depending on options.

Measurement example:
Pinpoint acquisition of 3 CH of attitude angle information (roll, pitch, and yaw angle/angular velocity)
with a gyroscope sensor


 

What can be done with measurement
Pinpoint acquisition of CAN signals to be checked without using a CAN analyzer.

- Easy to check on site, such as in a development vehicle.
- Analog output can be updated in 1 ms at the fastest.
- The one-channel type is reasonably priced and easy to use.
- For command control with arbitrary information in CAN-BUS, and for on-site confirmation of CAN output sensors.

Selection Points
CAN data conversion
- Easy-to-use 1-channel type with 1ms analog output and alarm output. 2.

Low price
- Data can be easily and inexpensively viewed with your own equipment (analog input), such as loggers and oscilloscopes.
- Low-cost CANL series also available: Analog output with 40ms update.

Products
Products Points Overviews
CAN-2401
CAN Analog
Converter
Product page

USB
Analog output
Alarm output
LINKSHIP compatible

Converts and outputs CAN digital values to voltage signals, etc.
Compact 24 x 48 size.
16bit analog output (1 ms).
LINKSHIP" compatible with power supply/logging/setting via USB.

CAN-2401: Panel mounting with indicator
CAN-2451: Without display, DIN rail mounting
CAN-2431: With indicator, DIN-rail mounting

CANL-2401
CAN Analog
Converter

[Low Price]
Product page

USB
Analog output
Alarm output
LINKSHIP compatible

Converts and outputs CAN digital values to voltage signals, etc.
Compact 24 x 48 size.
16bit analog output (40 ms).
LINKSHIP" compatible with power supply/logging/setting via USB.

CANL-2401: Panel mounting with indicator
CANL-2451: Without indicator, DIN rail mounting
CANL-2431: With display, DIN rail mounting



Customized products
The above models are customized products, such as boxed products.
　
  Name Input 16bit analog output Alarm
output		 Power
supply (V) 		External
dimensions		 Other features
  Update time

With SD logger
CAN Analog
Converter
[Custom boxed]

JPN page

CAN 2.0 0-10V
0-5V
±10V
±5V
4-20mA
【Select a model】		 1-9999ms/
40-9999ms
【Select a model】		 2 points/
4 points		 Selectable
AC100/
DC8-30
etc.
【Select a model】 		W 120
H 48
D 160
*Excluding
protrusions and legs.

- Equipped with slot for SD card
[With operation indicator LEDs]
Logging data storage

- Logging start/stop/ Power ON/OFF by front switch

- Rear connectors to choose from (any combination):
Terminal block BNC LAN Dsub, etc.


Example: 20CH type

Multi-CH type
CAN Analog
Converter

JPN page

Please consult us

Please
consult us

 DC 8-30
AC adapter
available 		W 126
H 53
D 128
*Excluding
protrusions and legs.

- Number of CHs to choose from

- Outputs to choose from
RS485, Ethernet, 16bit analog, HDMI, Alarm output, etc.

- Selectable rear connectors):
Terminal block BNC LAN Dsub USB-C, etc.

- LCD monitor: With/without (to be specified at the time of order):
Display timing, units, etc. can be freely set.

Please contact us for customization other than the above.
　Contact Us