Handy type CAN to analog converter [Customization]　CAN-HD 　　CAN to analog converters 　　All Products 　　HOME 　　>JAPANESE PAGE

*This is a customized product. Please consult us for specifications.

Converts CAN data to analog signals (voltage/current) and Ethernet　Desktop-grade performance anywhere

No need for complex settings No need for expensive CAN analyzers No need for expensive diagnostic equipment

Easy data conversion on site, no CAN analyzer required




CAN-BUS
 CAN High
→→→→→→
→→→→→→
CAN Low		 CAN-HD

↑

Power supply
4 x 3 batteries or
Included AC adapter

 Analog output
→→→→→
Check data with your equipment
Easy acquisition of CAN signals

Data loggers, oscilloscopes, etc.

Alarm output for easy alarm detection and trigger source for measurement.　[Please consult us]




CAN-BUS
 Specific CAN signals
→→→→→→		 CAN-HD

↑

Power supply
4 x 3 batteries or
Included AC adapter

 Alarm output
→→→→→		 External power source
 Voltage application
→→→→→		 Relay ON


Example of operation:　Acquisition of arbitrary signals from CAN output sensors
*Using our CAN analog converter: CAN-2401

CAN2.0 compatible 　[Input]
BPS 10k, 20k, 50k, 100k, 250k, 500k, 1Mbps
FORMAT INTEL [Little Endian] /MOTOROLA[(Big Endian]
FRAME Standard, 11bit length ID / Extended. 29bit length ID

Output variety
16bit analog output
Option
0-10V／0-5V／±10V／±5V／4-20mA 　[Select a model]　Output updated with each reception of CAN data
Alarm output
Option
2 points / 4 points　[ Depends on the model ]

2-way Power supply　 4 AA batteries Included AC Adapter
3-way Setting　
Setting buttons
Four buttons on the top of the main unit for instant setup		 PC+Setup management software
LINKSHIP [Free of charge]		 External setting device
PL-5A [Selling separately]
Selectable Connectors　
BNC＋terminal block  
 
 
 
From the right (back) side of the image
[For the included AC adapter]
[USB Type-C] For setup
[Digi-Switch] 　Not used, but may be used depending on your customization
[Terminal block]　For CAN input
[Pop-up BNC]　For other signal outputs　not used: may be used depending on customization
[Pop-up BNC]　For analog (voltage or current signal) output
 Pop-up BNC
Unique locking mechanism and pop-up BNC storage mechanism

[E.g.] Connector placement　Please consult with us about other items not listed below.

BNC ＋ 4-pole terminal block＊1
8-pole terminal block + 3-pole terminal block＊1
M8 ＋ 3-pole terminal block＊1
*1　Terminal block is screw type (M2 screw)

Easy-to-read OLED 16-character x 2-line display
　　Wide viewing angle and power saving
Carrying case included
Outside
A: Semi-hard material designed to protect stored items and be lightweight.
B: Loop-type band (removable) that can be attached to a belt, etc.
C: Round zipper with wide opening.
External dimensions 140W x 170D x 65H approx.		   Inside
D: Opens wide to give you a clear view of the items stored inside.
E: Elastic band to fasten the CAN-HD
F: Net for storage
  [Example of use]

E.g. of specifications　*This product is a customized product. Please consult us for specifications
Name CAN-Analog Output Converter [Customized product]
Model CAN-HD (tentative name)

CAN input section
Number of input 1 point
Communication standard CAN2.0B
CAN BPS 10k / 20k / 50k / 100k / 250k / 500k / 1M bps 　Set by program
CAN FORMAT INTEL (Little Endian) / MOTOROLA (Big Endian) 　Set by program
CAN FRAME Standard (11 bit long ID) / Extended (29 bit long ID) 　Set by program

Display section
Display unit 16 characters, 2 lines, character height 6mm OLDE
Display range 0.00000 - 999999　　
Decimal point position Set in program mode Number of digits 0 - 4
Display update time 0.1 - 9.9s Settable in 0.1s increments
Power ON/OFF indication Power switch LED lights up when ON

USB communication section（USB Type-C）
Specification USB2.0 (Serial port communication by USB virtual COM 230.4kbps)
Function Writing/reading set values

General Information
Operating temperature/humidity -10 °C to +50 °C / 35 to 85%RH (non-condensing) No corrosive gas
Ambient storage temperature --20 °C to +65 °C
Power supply Standard: AA battery 1.5V x 4 (DC6V)
AC adapter: Be sure to use the supplied AC adapter.
Power consumption 3W or less Sensor power output is not included.
When sensor power is output, the duration will be shortened due to current consumption.
Isolation Power supply / Other input/output
Withstand voltage Power supply/other I/O: 500V DC between each terminal for 1 minute
Dimensions 94 W×32 H×150 D [mm]
Accessories AC adapter, carrying case, 4 AA batteries (cable not included)

Analog output option
Output signal 0 - 10V／0 - 5V／±5V／±10V／4 - 20ｍA 【Select model】
D/A conversion DAC conversion method
Output resolution 16bit (58000 or more)
Load resistance Voltage output: 4.7kΩ or more / Current output: Please inquire
Output accuracy Voltage output: ±0.1% of FS at 23°C / Current output: Please inquire.
Temperature fluctuation ±200ppm／℃ or less
Output scaling Arbitrary scaling is possible by full scale and zero scale settings.
Output update Update with each CAN data reception

Alarm output option
Setting method Set in program mode
Number of Outputs 2 / 4: depending on model selection conditions
Output form with no polarity Isolated non-contact output [Photo MOS relay], The output circuit is an isolated non-contact output
When the operating condition of the comparator is [ON], the resistance value between COMP and COM: 50Ω max.
Output load voltage 280V AC/DC 100mA peak [resistive load] ON resistance 50Ω or less
Output logic Comparison is done with polarity [0 is greater than negative]
- More than: ON at the set value or more
- Less than: ON at the set value or less
- Within the range: ON within the set value, OFF out of the range
- Out of the range: ON out of the set value, OFF within the range
Update time Depends on analog output update time setting. Response time: 1ms [max]

CAN to analog converters

>Page TOP