| Front View |
¢ Recess for Stacking ¢ ¢¬ Protrusion for Stacking ¢¬ |
| View Applications > |
 Gear Sensors*, etc.
|
  |
 Line Driver LD Series*, etc.
|
 |
KAZ-Mighty KAZ-Mighty2 |
*When using a gear sensor with a line driver output (such as COCORESEARCH IMG12-50LD), a separate line driver is not required.
| Motor / Driver | |
Torque Converter, Clutch, etc. |
|
Load |
 |
|
|||
KAZ-Mighty2 |
||||
| What is PeriomaticTM? |
 |
Panel Mounting Bracket ATC-2 (Sold separately, set of 2) |
| Product Name | 2ch F/V Converter for Analysis |
| Model | KAZ-Mighty2 |
| Measurement Method | PeriomaticTM Method (Period Measurement Method) |
| Measurement Mode | SPEED / ùF (Deviation) / ùF AUTO (Automatic Deviation Tracking) |
| Input Section | |
| Input Ports | Phase A/B Reversible 2ch, or Single-Phase 2ch |
| Input Frequency | 0.23Hz - 250kHz |
| Measurable Deviation | ¡Þ1 - ¡Þ125kHz (Same for AUTO mode) |
| ùF AUTO Details | |
| Center Frequency Averaging | SIMPLE / MOVING |
| Averaging Time | 100ms / 200ms / 500ms |
| General-Purpose Input Signal | |
| Input Signal Form | Trigger level 0-9.99V, Zero-Cross (AC) |
| Input Sensitivity | 400 / 200 / 100 / 50mVp-p |
| Input Resistance | 10kΩ (Pull-down) / 6kΩ (+5V Pull-up) |
| Withstand Voltage | ±80V |
| Input Pulse | 0.2μs or more (both H and L), Trigger direction selectable |
| Input Coupling | DC / AC |
| AC Coupling Freq. Response | 35Hz (-3dB, 6dB/oct.) |
| Low-Pass Filter | None / 100k / 15k / 1.5kHz (-3dB, -6dB/oct) |
| Connectors | BNC, D-sub 15-pin (Loop-through) |
| Line Driver Input | |
| Input System | Line Receiver (26C32) |
| Input Sensitivity | ±200mV |
| Termination Resistor | None / 330Ω |
| Withstand Voltage | ±7V |
| Input Pulse | 0.2μs or more (both H and L), Trigger direction: Falling edge |
| Connector | D-sub 15pin |
| Sensor Power Supply | +5V 150mA / +12V 100mA (Cannot be used simultaneously) |
| Input Frequency Division | 1 - 255 (Hardware frequency division) |
| Display Section | ||
| Display Unit | 16¡ß2 character dot matrix LCD (with backlight) | |
| Display Digits | 7 digits (polarity, 5-digit measured value, decimal point) | |
| Zero Display | Reading zero suppression | |
| Display Update | 0.1s - 2.0s (in 0.1s increments) | |
| Frequency Accuracy | 0.001% ¡Þ1 Digit @ 23¡ëC | |
| Analog Calculation Section | |
| Measurement Resolution | 2.08ns (480MHz) |
| Calculation Response | 1 cycle + 6¦Ìs or less (90% output response at 1-pulse response) |
| Output Update | Every 1 input pulse or 1/2/5/10/20/50/100/200/500ms |
| 1ms during ùF AUTO measurement | |
| Moving Average | 1-pulse response: 1 - 100 times Time average: 1 - 100 times (at 1ms update) |
| Auto Zero | 5 stages *Dynamic prediction, SPEED mode only |
| Analog Output Section | ||
| Output Ports | BNC x 2 | |
| 2-Point Comparator | Comparator settings (Upper limit, lower limit, etc.) | |
| Output Resolution | 50000 or more | |
| Output Range | 0-10V / 0-5V / 1-5V / ¡Þ5V / ¡Þ10V / 4-20mA | |
| Calibration Output | 100% / 0% / -100% | |
| Temperature Drifts | ¡Þ200ppm/¡ëC or less | |
| Output Accuracy | ¡Þ0.05% Full Scale or less @ 23¡ëC | |
| Linearity | ¡Þ0.01% or less | |
| Load Resistance | Voltage output: 4.7k¦¸ or more / Current output: 510¦¸ or less | |
| Output Zero Adjustment Range | ¡Þ200mV / ¡Þ200¦ÌA | |
| Digital Output Section | ||
| Measurement Resolution | 6.25ns (160MHz) Display, Comparator, CAN, RS-232C, Ethernet | |
| Communications | |
| Communication Data | Measurement value output, Setting value read / write |
| CAN Communication | |
| Output Update | 1/2/5/10/20/50/100/200/500/1000ms |
| Standard | CAN2.0B Compliant |
| Baud Rate | 1M / 500k / 250k / 200k / 125k / 100k / 50k / 25k / 20kbps |
| FORMAT | Little endian / Big endian |
| ID Length | 11bit / 29bit |
| Termination Resistor | None / 120¦¸ |
| RS-232C Communication | |
| Output Update | 10/20/50/100/200/500/1000ms |
| Communication Method | Asynchronous |
| Parameters | Baud rate: 9.6/19.2/38.4/57.6/115.2kbps Start bit: 1bit Stop bit: 1bit Data length: 8bit Parity bit: None Communication code: ASCII |
| Ethernet Option | |
| Output Update | 10/20/50/100/200/500/1000ms |
| Network I/F Specs | Connector shape: RJ-45 Interface: 100BASE-TX/10BASE-T Auto-negotiation Communication compatibility: Ethernet Version2.0 / IEEE802.3 LED indicator: 100BASE-TX/10BASE-T, Link/Activity indicator |
| General Specifications | ||
| Rated Power Voltage | DC12-24V (Maximum allowable range: DC9¡¾30V) | |
| Power Consumption | 18VA or less | |
| Setup Memory | 8 profiles: Non-volatile memory (EEPROM) | |
| Isolation | Between Sensor power/Signal input, Analog output/Digital output, and Power input | |
| Dimensions | 218W ¡ß 218D ¡ß 57Hmm (including protrusions) | |
| Operating Temp./Humidity | 0¡ëC - +40¡ëC / 85%RH or less (no condensation) | |
| Storage Temp./Humidity | -10¡ëC - +60¡ëC / 85%RH or less (no condensation) | |
| Operating Atmosphere | No corrosive gases | |
| Weight | Approx. 1.8kg | |
| View F/V Converters List |