- Connects to torque sensors that output deviation frequency signals, flex fuel sensors, etc.
- Set center frequency, rated torque, and rated frequency as desired, and display torque value and fuel concentration.
- CAN (1ms update), 16bit analog (0.1ms update), alarm output, etc. are available. [Option].
- Frequency deviation is displayed in %, and ⊿F measurement is also available.

Torque sensor　　　　 Flex fuel sensor

Customization is possible, built into box, multi-CH, etc. 　　　 >Customization page Can be calibrated as an embedded product. Calibration documents and traceability charts can be issued. 19-inch rack mounting Built into box Multi-CH with indicator HDMI output + display software With SD logger ■Selectable measurement type and number of CHs　■Convenient, easy, low cost　■Customize input power and output signals to suit your facility

Output variety 40ms update

CAN output [Option] 3-wire wiring greatly reduces wiring compared to BCD Powerful error detection system for improved noise immunity and safety SAE J1939 [DLC 8 bytes or less] Customization experience available Please contact us for other customizations.

16bit analog output [Option] Resolution 50,000 or more／Full scale and zero scale settings, output zero adjustment Alarm output [Option]　 1 to 4points　[Depends on model] USB Type-C [standard feature]　 Data logging, setting, power supply

Input 600μHz - 1MHz,　resolution 10.4ns　

Supports signals	5V Logic	zero cross	NPN open collector	12V Logic	Customized Signals
Various options	Input Isolation	Line driver input	[Please contact us for more than 1 MHz]
Flexible adjustment	Trigger Level 0-9.99V	Hysteresis Select	Pull-up ON/OFF

Sensor power supply 5V/12V, other voltages are possible. [Option]

PERIOMATICTM calculation　 High accuracy from ultra-low speed to high speed. Follows sudden changes and stops. Moving averages Maximum 99 low cut function Stop judgment at or below the set value Additional Control Inputs［Option］HOLD, zero shift, etc.

About PERIOMATIC™ Read more Frequency measurement technology originally developed by COCORESEARCH

Reasonable and easy-to-use 1CH type

TQL-2401	Display only, Equipped with USB communication	17,600 yen and up* [tax not included]
TQL-2451	DIN rail mounting, no display, Comparator output 2 points	19,300 yen and up* [tax not included]

*Reference price in Japan.

Smart configuration and logging
Setting management, report printing, and CSV logging with dedicated software LINKSHIP [free of charge]　 >LINKSHIP page

CSV logging		Compare and match set value lists		PC save and copy of set values		Prevention of misoperation		Quickly set up multiple units
Time-specified logging, such as 600 seconds, is also available. Custom logger software is also available.		Multiple lists of set values can be compared and collated.		It prevents errors in note-taking and manual entry, and reduces management effort and costs.		Settings and confirmations can be made on the PC screen, preventing misoperation of the main unit's buttons.		Even multiple units can be easily configured by simply writing the configuration data.

USB Type-C connector standard: Setting, logging, power supply		Setup unit without LINKSHIP or PC required: Program Loader PL-5A　 [sold separately] 　 PL-5A Product Page *Setting only / data logging and power supply not available
Rear USB 2411 type also available.

Easy wiring and installation　On-site usability considerations

Simply connect the wires to the connector and plug it in by hand. Detachable Plug Connectors				Fixed Connectors [Customized support]non-detachable		Mounting hooks: Fixing the main body
	Spring lock type [standard]	M2 screw type [J04 option]				*Not included in 2431 and 2451 types.

Various ways to use

Carry and measure		Built in panel		DIN rail mounting
Carry PC, instrument, and cable, and measure with USB power supply. Storage case BXS-1 is also available.		24x48 size contributes to downsizing		One-touch fixture and display-less type are available.
BXS-1 Overview		TQL-24 Dimensions		DIN rail attachment [sold separately] BXF-DN2 page TQL-2451 Display-less type TQL-2431 With display type

Applications

See more Applications >

Torque and speed measurement of motors

	TQL-2401	Torque →	PLC, Logger, PC, etc.		Setting Example [A] Torque ±400N・m [B] Central frequency 60000Hz [C] Deviation frequency ±20000Hz Input-Output Relationship Input Output 40kHz [A] -400N・m 60kHz [B] 0N・m 80kHz [A] +400N・m
	SPDL-2401 Speedmeter/ Counter [Switchable]	Speed →

Flex fuel concentration measurement

TQL-2401

CAN USB Analog output Alarm output →

PLC, Logger, PC, etc.

Setting Example [A] Mixing ratio ±50% [B] Central frequency 100Hz [C] Deviation frequency ±50Hz Input-Output Relationship Input Output 50Hz [A] 0% 100Hz [B] 50% 150Hz [A] 100%

Torque to CAN conversion etc.

Specifications　

	Name Model Measuring method	Torque meter [frequency deviation meter] TQL-2401 PeriomaticTMB method Cycle calculation method
Input	Number of input points Input frequency Input resolution Input Signal Input method	1 point 0.0006Hz to 1.0MHz Approx. 10.4ns (96MHz) 5V logic, zero cross, NPN open collector, 12V logic, input customized signal Single-phase signal
[*] General-purpose input option	Input Level and Sensitivity	5V logic Zero-cross NPN open collector 12V logic Customized input	Trigger level 2.5V 0V 2.5V 6V 0-9.0V in 10mV units	Hysteresis ±0.4V ±0.03V ±0.4V ±0.4V Small:±0.03V, Medium : 0.4V, Large: ±1.3V, trigger level 4.7V or lower/ ±2.6V, trigger level 4.7V or higher
	Input pulse Input resistance Input withstand voltage	[Small] [Medium] 0.2 μs or more 　　[Large] 0.3 μs or more, for both H and L levels 5V logic, zero cross, NPN open collector, and Input customized signal (trigger level 4.7V or lower): 10kΩ 12V logic, input customized signal (trigger level 4.71V or higher): 5kΩ ±30V　　*Inputs and outputs are not insulated for the general-purpose input option.
[D] Line driver input option	Input signal Input withstand voltage Recommended line driver Termination resistance	Line driver signal ±25V (differential voltage) Equivalent to AM26LS31 300Ω (standard specification)　　*Input and output are isolated for the line driver input option.
	Input low-pass filter Trigger edge Input withstand voltage Input connector Sensor Power supply output[Option]	Select from OFF, 500Hz, 5kHz, 120kHz, or 800kHz Fall ±30V Spring lock plug connector / [J04 option] M2 screw type plug connector [H] DC +12V±5％ 60mA max / [L] DC +5V±5％ 150mA max *When USB power is supplied, sensor power is not output.
Calculation	Measurement mode Calculation rate Frequency divider ratio Output moving average Dynamic PredictiveTM Hold function 　 Additional control input Low cut function Dual range	Custom (Torque) / Frequency meter / Period meter (seconds only) Center frequency, deviation frequency at rating, rated torque, and output polarity are set for input frequency. 1 to 60000 1 to 99 8 levels (including continuous and stop prediction)　 1 point, Set from current value, maximum value, minimum value, maximum fluctuation range (Hold input, Additional control input) ON when shorted to GND, OFF when open (hold function is set) 2 points, ON by short-circuiting to GND, OFF by opening (hold function assigned and set for each input) Low cut function Stop judgment at a speed lower than the set value Two different calculation rates can be set 　 *Selected by hold input according to hold function assignment
Display	Display Color Indicator (Numerical Display) Decimal point position Display update time Display accuracy Indicator	Red LED 5-digit, 7-segment LED Character height 9mm / Display range:-19999 to 99999 Polarity indication: Reverse rotation -Lighted / Over indication: OL / Zero indication: Leading zero suppress Semi-fixed Decimal point position is set in program mode. [0] *****, 　[1] ****.* to [4] *.**** 0.3 sec (settable from 0.1 to 9.9 sec) 20ppm ± 1 digit LED 1 point (selected from power/ control input/ trigger/ comparator output)
USB communication	Communication specification Communication function Output update time	USB2.0 (Serial port communication by USB virtual COM 230.4kbps) Writing/reading of set values/continuous output of measured values 40 to 9999.9ms, settable in 0.1ms increments (No output when output update time is set to 1 to 9)
General Information	Operating temp./humidity Power supply voltage Power consumption Isolation Withstand voltage Weight	-10°C to +50°C / 35 to 85%RH (non-condensing) 7 to 30V DC with reverse connection protection. Power supply from USB host: 5V 3W or less [General-purpose input type]: Power supply / Other input/output [Line driver input type]: Power supply / Frequency signal input / Other input/output Between each terminal of the above isolations: 500V DC between each terminal for 1 minute Approx. 60g
CAN Option	Communication specifications Communication function Setting item Output update time	CAN2.0B 10 k / 20 k / 50 k / 100 k / 250 k / 500 k / 1M bps, [Format] INTEL/MOTOROLA, [Frame] 11bit/29bit Writing/reading of set values/continuous output of measured values CAN transmit ID, CAN receive ID 40 to 9999.9 ms (settable in 0.1 ms increments) (When output update time is set to 1 to 9, instantaneous values are output every 1 ms.)
RS-485 communication option	Number of connected units Communication format Communication method Communication standard Communication speed Data format Communication code Communication function	32 units (max.) 2-wire multi-drop serial communication Asynchronous RS-485 9,600 /19,200 /38,400bps Set in program mode Start bit: 1 bit / Stop bit: 1 bit / Data length: 8 bits / Parity bit: None ASCII Writing/reading set values/measurement value output (response to request command) Modbus RTU support is available upon request.
Analog output option	Output signals D/A conversion method Output resolution Load resistance Output accuracy Temperature fluctuation Output scaling Output update time Input/output delay time	[E1] 0 to 10 V, [E5] 0 to 5 V, [R1] ±10 V, [R5] ±5 V, [I1] 4 to 20 mA　　　 [Select a model] DAC conversion method 16bit (50,000 or more) [Voltage output] 4.7kΩ or more / [Current output] 300Ω or less [Voltage output] ±0.1% of FS @ 23°C / [Current output] ±0.1% of FS @ 23°C ±200ppm/℃ or less Arbitrary scaling is possible by full scale and zero scale settings 40 to 9999.9ms settable in 0.1ms increments Output update time + analog rise time 150 μs max.
Alarm [Comparator] output option	Setting method Number of outputs Output form Output load voltage Output logic Update time	Set in program mode 2 points (or 1 point) Depends on model selection conditions. 1 point for line driver input and analog output with comparator output specification. Isolated non-contact output (photo-MOS relay) No polarity. When comparator operating condition is ON, resistance between COMP and COM 50 Ω or less for C2 option (2 comparator) / 100 Ω or less for C1 option ( 1 comparator) Peak AC/DC280V 100mA (resistive load) / ON resistance 50Ω or less Comparison is made with polarity (0 is greater than minus) [Over] ON when set value or more / [Under] ON when set value or less Depends on analog output update time setting. Response time 1ms (max)